Apex's Trusted HVAC Repair Experts: ACs, Heat Pumps, Furnaces & More!

I performed routine heating maintenance on a residential property. I checked the furnace, thermostat, and air filters, and made any necessary adjustments to ensure optimal performance. I also cleaned the vents and registers to improve air quality. The homeowner was very pleased with the results.

I recently completed a heating maintenance job on two units. I replaced the air filters, cleaned the coils, and checked the electrical connections. I also made sure that the thermostat was working properly. The clients were very happy with the results.

I recently completed a routine heating maintenance job for a client. This involved inspecting and cleaning the furnace, checking the thermostat, and replacing the air filter. I also provided the client with tips on how to maintain their heating system and ensure it runs efficiently.

I replaced the third-floor evaporator coil in a residential home. The evaporator coil is located in the air handler unit and is responsible for cooling the air before it is distributed throughout the home. The coil was leaking, so I removed the old coil and replaced it with a new one. I also cleaned the evaporator fins and checked the refrigerant levels.

I performed a routine heating maintenance on a new unit. I checked the system's functionality, cleaned the filters, and made sure the unit was operating at peak efficiency.

"I was called to a job where the outdoor unit was making a loud rumbling noise. I arrived and found that the fan motor had seized up, causing the unit to overheat. I replaced the motor and the unit was back to normal.

I supplied a free quote on duct work and installation of a unit.

I performed routine heating maintenance on a residential property. I checked the furnace, thermostat, and air filters and made any necessary adjustments. I also cleaned the vents and registers to improve airflow.

I was called to a new home to perform a heating maintenance on a new unit. The client was very pleased with the work I performed.

I performed routine heating maintenance on a residential property. I checked the furnace, thermostat, and air filters, and made any necessary adjustments to ensure optimal performance. I also cleaned the vents and registers to improve air quality.

We recently completed a two-unit heating maintenance project. We replaced the old furnace and air conditioner with new energy-efficient models, ensuring optimal performance and energy savings for our clients.

I replaced the evaporator coil under warranty.

I completed a heating maintenance job on three Lennox units. I inspected the units, cleaned the burners, inspected the heat exchanger, and replaced the air filter. I also checked the electrical connections and tested the thermostat.

I performed routine maintenance on a unit heating system. I checked the system's components, including the thermostat, furnace, and air conditioner, and made any necessary adjustments or repairs. I also cleaned the filters and inspected the ductwork for any leaks or damage.

I replaced the pressure switch system in a customer's home. The old system was failing, and the customer was experiencing no heating. I removed the old system and installed a new one, ensuring that it was properly sized and installed according to manufacturer specifications. The customer was very happy with the results, and I was able to provide them with a warranty on the work.

I am a highly skilled and experienced home service professional. I recently completed a routine heating maintenance job for a client. The job involved inspecting and cleaning the heating system, checking for any potential issues and making necessary adjustments. I also provided the client with tips on how to maintain the heating system and prevent future problems. The client was very satisfied with the job and expressed gratitude for my professionalism and expertise.

I recently completed a routine two-unit heating maintenance. I inspected the units for any issues and made the necessary repairs. I also cleaned the filters and checked the thermostat settings. The homeowners were very pleased with the service and thanked me for my professionalism.

I recently completed a routine heating maintenance job for a client. It involved inspecting and cleaning the heating system, checking for any potential issues, and making necessary adjustments to ensure optimal performance. I also replaced the air filter and cleaned the blower wheel to improve airflow and efficiency. The client was very satisfied with the results and expressed gratitude for the professional and timely service.

I performed a routine heating maintenance tune-up on a residential property. This involved inspecting and cleaning the heating system, checking for any potential issues, and making necessary adjustments to ensure optimal performance. I also provided recommendations for improving energy efficiency and discussed any maintenance tasks that may be needed in the future.

Repaired Rheem heat pump with defrost board failure. Installed new RHEEM-50027 control board. Calibrated outdoor thermistor. Set defrost timer dip switches. Tested defrost cycle operation. Verified proper reversing valve operation. System resumed normal heating and defrost cycles.

Serviced Trane CleanEffects air cleaner. Cleaned collection cells with pressure washer. Replaced worn corona wires. Tested voltage output with multimeter. Cleaned pre-filter and field chargers. Verified proper ionization and collection cell operation. Particulate removal efficiency improved to 99.98%.

Installed Mitsubishi indoor unit using quick-hang bracket. Ran line set through wall sleeve. Flared connections using Imperial tool. Pressure tested to 550 PSI. Pulled vacuum to 200 microns. Charged with R410A. Programmed wireless remote.

Repaired Bryant Evolution furnace with pressure switch error. Cleared blocked condensate line using CO2 blaster. Replaced cracked drain trap. Installed new pressure switch rated at -0.65" W.C. Tested draft with digital manometer. Verified proper condensate flow and switch operation.

Repaired Lennox XC21 condenser with failed compressor. Recovered R410A using Yellow Jacket recovery machine. Replaced Copeland scroll compressor. Installed new filter drier and Schrader cores. Pressure tested with nitrogen. Evacuated to 250 microns. Recharged to factory specifications using digital scale.

Installed Honeywell F300 electronic air cleaner. Mounted between return plenum and air handler. Connected to dedicated 120V circuit. Set ionization voltage to recommended level. Added pre-filter for larger particles. Tested operation with particle counter. Air quality improved by 85% after installation.

Resolved low airflow issue in Bryant Evolution system. Cleaned evaporator coil with Nu-Calgon Evap Pow'r-C. Adjusted blower speed using Evolution connex controller. Sealed duct leaks with Hardcast 321 water-based sealant. Measured static pressure with Testo 510i manometer. Airflow increased from 850 to 1200 CFM.

Repaired Rheem RGGE gas furnace with intermittent ignition failure. Cleaned flame sensor with emery cloth. Replaced worn hot surface igniter. Adjusted gas pressure to 3.5" W.C. using Dwyer manometer. Verified proper flame signal with Fieldpiece SC260 clamp meter. Tested safety switches. Heat output and reliability improved.

Installed Lennox PureAir S air purification system. Mounted cabinet on return air plenum. Wired UV lamp to dedicated 24V transformer. Installed MERV 16 carbon filter. Connected to Lennox iComfort S30 thermostat for monitoring. Tested air quality improvement using AirAdvice for Homes IAQ monitor.

Fixed refrigerant leaking schrader valve. Recovered remaining refrigerant with Appion G1Single recovery machine. Replaced faulty core using Imperial 535-C valve core tool. Pressure tested to 450 PSI with nitrogen. Evacuated system to 350 microns. Recharged with factory-specified R410A amount using digital scale.

Serviced clogged condensate drain line. Cleared blockage using CO2 blaster and wet/dry vacuum. Flushed line with diluted vinegar solution. Installed EZ-Trap inline p-trap with clean-out port. Added condensate treatment tablets to prevent future biological growth. Verified proper drainage.

Replaced worn contactor in outdoor unit. Disconnected power and removed old contactor. Installed new Packard C230A 2-pole 30 amp contactor. Checked coil voltage and continuity. Cleaned and tightened all electrical connections. Tested operation under load with amp clamp. Unit cycled normally after repair.

Corrected refrigerant overcharge. Recovered excess R410A using Appion G5Twin recovery machine. Weighed removed refrigerant with AccuTools digital scale. Recharged to manufacturer specifications. Verified superheat and subcooling with Testo 550s digital manifold. System efficiency improved by 10%.

Today, I installed a Mitsubishi Electric ductless mini-split system for both heating and cooling. The homeowner wanted an efficient solution for a home addition. I mounted the indoor air handler and connected it to the outdoor condenser. I ran refrigerant lines and wiring, then charged the system and tested it for both cooling and heating functions. The new mini-split provides excellent comfort control in the space, without the need for extensive ductwork.